Commercial · Hollywood, FL
A concrete loading dock has to take constant impact from forklifts, pallet jacks, and truck traffic without cracking or settling. Quality Concrete Hollywood has served Hollywood since 2019, building and repairing loading docks and aprons with the right slab thickness, reinforcement, and drainage details for commercial wear.
Prep starts with demolition or sawcutting to clean, square edges, then proof-rolling the subgrade to find soft spots. We excavate to the required depth, install compactable base rock (typically 6-12 inches depending on loads), and compact in lifts with a plate compactor or roller to reduce future settlement. Forms are set to proper elevations and slopes, dowels are drilled and epoxied where we tie into an existing slab, and we place a vapor barrier where needed for interior dock slabs. Before concrete arrives, we confirm reinforcing steel (rebar grid or wire mesh) is supported on chairs, and we plan control joints and isolation joints to manage shrinkage movement.
South Florida conditions demand attention to drainage, chloride exposure, and daily heat. We shape the dock approach and apron to move water away from the building, add thickened edges where trucks turn, and protect slab transitions to reduce corner breaks at overhead doors. For finish, we match the use: broom-finish for traction on aprons and ramp lanes, hard trowel for interior or covered dock slabs, and edge tooling at docks where impacts are common. When specified, we can include fiber reinforcement, air entrainment where appropriate, and a penetrating silane or siloxane sealer to reduce water and salt intrusion that leads to spalling.
Hollywood businesses choose us because we build for real loading conditions, not just curb appeal. Our crews handle new pours, dock apron replacement, and structural patching, including rebar doweling, epoxy crack repair, and full-depth panel replacement when the base has failed. You get clear scope, straightforward scheduling around deliveries, and a plan that keeps your site safe, from barricades and cones to clean sawcut lines and debris haul-off. We are licensed and insured, and we provide a free written estimate with slab thickness, reinforcement, joint layout, and finish spelled out.
On completion, we walk the dock and apron with you to verify slopes, door clearances, and joint placement, and to confirm any tie-ins meet flush tolerances for forklift travel. We explain cure time, traffic restrictions, and when trucks can return, plus options like joint sealing, non-slip traction grooves, and sealing for easier wash-down. You receive a clean, ready-to-use concrete loading dock area with proper control joints, neat edges, and a base built to resist settlement. If we find issues that affect performance, such as unstable subgrade or drainage problems, we document them and offer corrective options before they turn into repeat cracking.
seo_block_placeholder
Yes. We provide a free written estimate after reviewing the site conditions, access, elevations, and scope.
Yes. Quality Concrete Hollywood is licensed and insured for concrete contracting work.
Yes. We can sawcut, break, remove, and haul off existing concrete, then rebuild the base, forms, and reinforcement before the new pour.
In many cases, yes. We can match common finishes like broom-finish and light salt-finish, and we plan joint layout and edges to blend with adjacent flatwork.
Pricing depends on square footage, thickness, reinforcement, base work, demolition/haul-off, access, drainage corrections, and finish and sealing requirements. A site visit helps us give an accurate written number.
If your concrete loading dock is cracking, sinking at the approach, or spalling at the door line, the problem is usually a mix of heavy point loads, poor base compaction, and water intrusion. Quality Concrete Hollywood builds and repairs loading docks and aprons for warehouses, retail back-of-house areas, and commercial properties, focusing on slab thickness, reinforcement, drainage, and jointing so forklifts and trucks can work without constant patching.
A concrete loading dock system typically includes the dock slab, door line transition, ramp lanes, and the exterior apron where trucks turn and back in. Getting these areas right means planning elevations, slopes, and thickened edges, then placing concrete with consistent consolidation and finishing. We sawcut control joints on schedule, install isolation joints where the slab meets walls or columns, and address weak transitions with dowels or full-depth replacement instead of thin overlays that fail under wheel loads.
For repairs, we start by identifying the cause, not just the crack. If the slab has settled, we evaluate the base and drainage and recommend full-depth panel replacement when needed. If the concrete is sound but worn, we can handle edge rebuilds, spall repairs, joint rebuilding, and crack injection with epoxy, then protect the surface with a penetrating sealer. The goal is a flat, durable travel path that reduces forklift vibration, protects door hardware, and limits water entry.
Whether you need a new concrete loading dock apron pour or targeted repairs, we provide a written scope that includes thickness, reinforcement, joint plan, finish, and cure requirements. Work is staged to keep deliveries moving when possible, with clear safety controls and a clean jobsite at closeout. Request a free written estimate and we will recommend the most durable, cost-effective fix for your dock traffic.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Hollywood. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
