Commercial · Hollywood, FL
Protect storefronts, loading areas, and pedestrian zones with concrete bollard installation from Quality Concrete Hollywood, serving since 2019. We set new bollards and replace damaged posts with properly sized footings, straight layouts, and durable finishes that hold up to daily traffic in Hollywood.
Every reliable bollard starts below grade. We verify the layout, mark offsets from curbs and doors, and call 811 before any excavation. After digging to the required depth, we compact the subgrade, add a crushed stone base where needed, and set forms so the footing stays square. Steel pipe or schedule-rated bollards are plumbed with temporary bracing, then we pour a high-strength concrete mix and consolidate it to reduce voids and honeycombing.
South Florida sites bring their own variables, high water table, sandy soils, tight drive lanes, and salt air. We adjust excavation and dewatering as needed, keep reinforcement properly chaired, and maintain clear cover so steel is protected. Above grade, we finish for both function and appearance, broom-finish concrete where slip resistance matters, clean trowel edges at control joints, and smooth collars around posts. If you need visibility, we coordinate protective sleeves, reflective bands, and paint-ready surfaces that accept exterior coatings without flaking.
Hollywood property owners choose us because we install bollards like a contractor, not a handyman. You get accurate layouts, consistent spacing, and footings sized for real impacts, not undersized holes filled with bag mix. Our crew shows up with the right equipment for clean work, rotary hammer drills for core drilling into existing slabs, rebar cutters, mixers or ready-mix scheduling, levels, and proper bracing so posts cure plumb. Quality Concrete Hollywood is licensed and insured, and we provide a clear written scope so you know exactly what is included.
Before we wrap up, we do a walkthrough to confirm post locations, clearances for doors and ADA paths, and any protection needed for nearby asphalt or pavers. We check that the concrete is finished clean, the bollards are aligned, and the site is left safe while curing. You receive a written estimate, a straightforward plan for cure time and return-to-service, and options for add-ons like concrete pads, curb repairs, and replacement of spalled slab edges around damaged posts. If you are replacing existing bollards, we can demo, haul away debris, and reset new posts to match your site plan.
Yes. We provide a free written estimate after reviewing the site conditions, access, elevations, and scope.
Yes. Quality Concrete Hollywood is licensed and insured for concrete contracting work.
Yes. We can sawcut, break, remove, and haul off existing concrete, then rebuild the base, forms, and reinforcement before the new pour.
In many cases, yes. We can match common finishes like broom-finish and light salt-finish, and we plan joint layout and edges to blend with adjacent flatwork.
Pricing depends on square footage, thickness, reinforcement, base work, demolition/haul-off, access, drainage corrections, and finish and sealing requirements. A site visit helps us give an accurate written number.
Concrete bollard installation is one of the most cost-effective ways to protect people and property from vehicle strikes. Quality Concrete Hollywood installs new bollards and replaces damaged posts for storefronts, warehouses, HOAs, schools, gas stations, and parking areas. Our process focuses on correct footing size, solid base prep, plumb alignment, and a durable concrete finish that resists cracking, settlement, and corrosion exposure common in South Florida environments.
A dependable bollard install starts with planning. We confirm spacing, offsets, and any conflicts with utilities, irrigation, or existing reinforcement, then schedule locates before digging. Depending on the application, we excavate for a concrete footing, set the pipe bollard, and place concrete with consolidation to reduce air pockets. For retrofits, we can core drill through an existing slab and tie into the concrete with dowels where appropriate, then patch and finish to blend with surrounding flatwork.
Local conditions matter. Sandy soils and a high water table can cause shifting if the base is not prepared correctly, so we focus on stable subgrade, compacted backfill, and proper curing practices. Above grade, we finish the concrete to control water shedding and reduce trip hazards, and we can coordinate protective sleeves and paint-ready surfaces for high-visibility safety requirements. If you have existing damage, we can also address spalled slab edges, broken curbs, and failed patches around previous bollards.
If you need concrete bollard installation in Hollywood, we will provide a free written estimate with a clear scope, timeline, and site requirements. Tell us the number of posts, the area to protect, and whether this is new work or replacement, and we will recommend a practical layout and install method that fits your property and traffic patterns.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Hollywood. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
